Serving sailors online since 1997
 
 

Recent Topics

jim01749 at 3:02am 04.25.24
7/247
We have a 2008 Hunter 45 CC and was looking for correct size and maybe some tips on how to install n
brad minda at 10:35pm 04.24.24
0/157
I am noticing aboit an 1/8 inch movement on the upper ruder post bushing each way side to side 1/4 i
Jerry1956 at 6:01pm 04.24.24
12/366
First off apologies if this is a redundant topic for this thread. We just sailed our new (to us) 20
slorandy at 4:27pm 04.24.24
3/305
Had the drive gear for the injector pump come off (apparently the nut came undone). Had a diesel me
dkinzer at 11:18am 04.24.24
2/179
Both bow rollers on our 2007 41AC look like the one on the right in the photo. None of the cracks se
Fred at 9:51am 04.24.24
4/202
My Cat28 MKii uses the (discontinued) OEM shroud turnbuckles as shown below. There is limited space
Necessity at 8:35am 04.24.24
4/150
Good Morning, Just completed a full electrical refit after encountering a low voltage problem that w
anelso29 at 8:28am 04.24.24
6/649
Hey everyone, I apologize for the basic questions, but I truly appreciate everyone's knowledge on t
teacherspet at 6:56am 04.24.24
8/295
I have to replace two rivets on my Vision 32 Vang Bracket on the mast. Does anyone know if Hunter us
ant302 at 5:16pm 04.23.24
8/280
Inherited the hot mess of batteries below when I purchased the boat 2 years ago. I am looking to re
seadaddler at 4:15pm 04.23.24
1/147
Help before I take on this projects.07 H-36 6
karellen at 3:28pm 04.23.24
1/242
Hello. The last time we used the shower on board our H356, we had water streaming out into the cabin
Tally Ho at 2:49pm 04.23.24
44/1404
toastysailor at 2:46pm 04.23.24
10/364
I have a 2023 Oceanis 34.1. Due to the location of the shrouds, I am extremely limited in how far o
BKParks at 2:03pm 04.23.24
4/227
Hello, I want to replace my starter. I believe my brushes are starting to go. I bought a new one re
Brianstanis at 12:04pm 04.23.24
8/305
Hello everyone. I went to my Hunter the other day to begin Spring prep work to get it ready for laun
Drinky Crow at 10:13am 04.23.24
9/367
Hows about this? Or? Or? https://www.rustoleum.ca/-/media/DigitalEncyclopedia/Product/RustoleumCA/Pr
Ringydingydo at 9:32am 04.23.24
3/280
On my 1989 Hunter Legend 37, the main halyard is likely 1/2 inch, maybe a little thicker and well wo
marchem at 8:32am 04.23.24
23/657
xavpil at 5:49am 04.23.24
11/304

Recent Replies

Epoxy vs Varnish
Plymouth Sailor at 5:19pm 05.16.24
This is a pine stern seat. I sanded it and covered it with a coat of epoxy. Then since I planned to
Epoxy vs Varnish
Plymouth Sailor at 5:19pm 05.16.24
Expoy is great for sealing wood! Cured epoxy will turn yellow with UV exposure so you would still n
Epoxy vs Varnish
Plymouth Sailor at 5:18pm 05.16.24
Epoxy vs Varnish   (1)
jssailem at 5:16pm 05.16.24
This is a pine stern seat. I sanded it and covered it with a coat of epoxy. Then since I planned to
Epoxy vs Varnish
MikeHoncho at 5:07pm 05.16.24
Epoxy vs Varnish
kbgunn at 4:51pm 05.16.24
Expoy is great for sealing wood! Cured epoxy will turn yellow with UV exposure so you would still ne
Fuel tank fitting for pick up tube and fuel shut off for "83 O'Day 28   (2)
Allan12210 at 4:14pm 05.16.24
If it looks anything like mine, remove the fuel hose from the shut off valve. The aluminum block wit
23.5 outboard motor
Southern Crux at 2:46pm 05.16.24
Thanks everyone for all the recommendations. I went and checked up on the status today of my current
Gooseneck Pin
AndyL at 2:32pm 05.16.24
Seems like you're not the only one... Gooseneck On 1992 Hunter 33.5
Has anyone installed new Companionway Slider Track Felt?
AndyL at 1:53pm 05.16.24
That's a great help - and thanks for the advice about dry lube. I checked out some pictures online
So It Begins: Deck Recoring Project
jibes138 at 1:40pm 05.16.24
Very ambitious of you. Looks good so far. I saw a guy recore around his chainplates on a caliber 3
Fuel tank fitting for pick up tube and fuel shut off for "83 O'Day 28
jibes138 at 1:22pm 05.16.24
pick up tube for what? Sorry I just read your headline. It might be plastic, some of them have a sc
1985 O'day 28 Depth Transducer Relocation - Something Interesting
jibes138 at 1:16pm 05.16.24
I used G10 sheet stock for my backing plates when I replaced my through hulls and valves with seacoc
out haul cleat
isaksp00 at 12:44pm 05.16.24
On my H23 I just coiled the line with fairly small loops and let it hang, on one of the reefing rams
End of Times
isaksp00 at 12:42pm 05.16.24
Will your handle become "trawlergunner"?
23.5 outboard motor
Sail22Capri22 at 12:13pm 05.16.24
I have a Capri 22 with the 6HP Tohatsu 20". The motor has been great and plenty of power even when g
Air Conditioner Condenser Pump
kloudie1 at 11:14am 05.16.24
Yup, exactly the same pump function.... That is the subject of my wondering.. seems like it could wo
Removing caulk....
NYSail at 11:05am 05.16.24
Air Conditioner Condenser Pump
Terry Cox at 10:37am 05.16.24
The pump pumps water into the exchanger then the warmer water exits from a thru-hull. Hi Claude. I

Copyright 1997-2024 SB Owners, LLC
All rights reserved.

is not endorsed by or affiliated with any sailboat manufacturer.